Item Description:
DC motor is a rotating motor that can convert DC electric vitality into mechanical strength (DC motor) or mechanical strength into DC electric vitality (DC generator). It is a motor that can transform DC and mechanical energy into a single another. When it operates as a motor, it is a immediate present motor, which converts electrical strength into mechanical power when it runs as a generator, it is a direct present generator, which converts mechanical power into electrical energy.
| Merchandise Title | Spot Offer of Modest and Medium DC Motor in Z4-315-21 160KW 440V 500rpm Motor Plant |
| Motor Sort | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition composition | The construction of DC motor should consist of two elements: stator and rotor. The static portion of DC motor is referred to as stator. The major perform of stator is to make magnetic field, which is composed of foundation, major magnetic pole, commutation pole, end cap, bearing and brush system. Running portion is known as rotor, whose principal operate is to generate electromagnetic torque and inductive electromotive drive. It is the hub of vitality conversion of DC motor. So it is also generally called armature, which is composed of rotor, armature main, armature winding, commutator and fan. |
| Model | Z Sort |
| Seat variety | Z315-Z1000 |
| energy | 60~2800kW |
| Voltage | 220~1000V |
| Torque assortment | one.5 ~180kNm |
| Safety degree | IP23, IP44 |
| Cooling manner | IC06,IC17,IC37,IC81W |
| Working pace | Constant Pace /Minimal Speed /Change Velocity /High Speed Other |
| Main classification | DC Motor is a device that converts mechanical power into DC electricity. It is primarily used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation electrical power provide of alternator. Even though in areas where DC energy is needed, AC power rectifier is also used to change AC into DC energy, but from some facets of overall performance, AC rectifier electricity source can not totally substitute DC generator. |
| Software | DC motors are commonly used in tape recorders, online video recorders, online video discs, electric powered shavers, hair dryers, electronic watches, toys and so on. |
| Upkeep strategy | Specialist motor upkeep heart motor upkeep procedure: cleaning stator and rotor – replacing carbon brush or other areas – vacuum F strain dipping paint – drying – Calibration balance. one. Use environment should be usually dry, motor surface area ought to be held cleanse, air ingestion must not be hindered by dust, fibers and other obstructions. 2. When the thermal safety of the motor carries on to run, it should be ascertained no matter whether the fault will come from the motor or the overload or the placing benefit of the protective system is as well reduced. Right after reducing the fault, it can be place into procedure. 3, make sure that the motor is effectively lubricated during operation. The general motor runs for about 5000 hrs, that is to say, lubricating grease must be included or replaced. When bearing overheating or lubricating deterioration is found in operation, the hydraulic stress need to change lubricating grease in time. When changing grease, the aged grease must be taken off, and the oil groove of bearing and bearing go over ought to be washed with gasoline. Then ZL-3 lithium grease ought to be filled with 1/two (two poles) and 2/three (4 poles, 6 poles and eight poles) of the cavity among the inner and outer rings of the bearing. four. When the daily life of the bearing is more than, the vibration and sounds of the motor will increase naturally. When the radial clearance of the bearing reaches the following worth, the bearing should be changed. five, when eliminating the motor, it is Okay to take away the rotor from the shaft extension or the non extension conclude. If it is not required to unload the enthusiast, it is a lot more practical to get out the rotor from the non-axle extension finish. When pulling out the rotor from the stator, the stator winding or insulation should be prevented from currently being damaged. 6. When changing the windings, the type, dimensions, turns and gauges of the original windings should be recorded. When these info are misplaced, they must be obtained from the maker and the original made windings need to be changed at will, which frequently deteriorates one particular or a number of performance of the motor or even can make it unattainable to use them. |
